The project variant is ALLMODES. CONFIGURED Frames (IPDU) DESCRIPTION : ---------------------------------------------- FRAME NAME: DiaOBDMotor_A Diagnose OBD Motor (DIAG_OBD_ENG) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages CanDLC: 7 CanNode: CAN_A CanID: 0x397 Taskcycle: FRMSCH_TXMODE3 Frame time : FRMSCH_TXMODE3*10 in ms Timeout: FRMSCH_TXMODE3*0 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_TXMODE3*10 in ms Signals: ::::0x397, DiaOBDMotor_A, Status_OBD_Zyklus (ST_OBD_CYC), Com_stOBDCtl ::::0x397, DiaOBDMotor_A, no signal (FREI), Com_DummyTx2 ::::0x397, DiaOBDMotor_A, OBD_Position_Drosselklappe_Motor (OBD_PO_THVA_ENG), ThrVlv_rPs ::::0x397, DiaOBDMotor_A, OBD_Modellwert_Last_Motor (OBD_CALCVL_LD_ENG), CoETS_rTrq IDPUCallback: Frm_ApplCpySigChgBuffer_pfn FRAME NAME: DriveTrainData1_FA Daten Antriebsstrang 1 (DT_PT_1) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages CanDLC: 6 CanNode: CAN_B CanID: 0x3fb Taskcycle: FRMSCH_TXMODE3 Frame time : FRMSCH_TXMODE3*10 in ms Timeout: FRMSCH_TXMODE3*0 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_TXMODE3*10 in ms Signals: ::::0x3fb, DriveTrainData1_FA, Soll_Drehzahl_Leerlauf_Antrieb_Erweitert (TAR_RPM_IDLG_DRV_EXT), HLSDem_nSetPLoExt ::::0x3fb, DriveTrainData1_FA, Status_Bereitschaft_Fahren (ST_RDI_DRVG), SwSABMW_stRdiDrvg ::::0x3fb, DriveTrainData1_FA, Status_KAT_Heizung (ST_CAT_HT), SwSABMW_stCatHeatgActv ::::0x3fb, DriveTrainData1_FA, Anforderung_Schaltpunktanpassung_Getriebe_Ladebilanz (RQ_SHPA_GRB_CHGBLC), Com_stShftPointGbxDem ::::0x3fb, DriveTrainData1_FA, Status_Schubabschaltung_Antrieb (ST_INFS_DRV), Com_stOvrRun ::::0x3fb, DriveTrainData1_FA, Status_Drehungleichförmigkeit_Antrieb (ST_RTIR_DRV), Com_stInjDu ::::0x3fb, DriveTrainData1_FA, Steuerung_Shiftlock_Antrieb (CTR_SLCK_DRV), Com_stSLck ::::0x3fb, DriveTrainData1_FA, Anforderung_Anfahrhilfe_Motorsteuerung (RQ_STASS_ENGMG), Layer_stNdStrtUpSupp ::::0x3fb, DriveTrainData1_FA, Auswahl_Bus_Kommunikation_Motor_Getriebe (SLCTN_BUS_COMM_ENG_GRB), Com_stDDEBusActv ::::0x3fb, DriveTrainData1_FA, Anforderung_Schaltpunktanpassung_Getriebe_Regeneration_Partikelfilter (RQ_SHPA_GRB_REGE_PAFI), Com_stAdptShftPoint ::::0x3fb, DriveTrainData1_FA, Absenkung_Abregelung_Drehzahl_Antrieb (RDUC_DOCTR_RPM_DRV), Com_stRdcDwnCtlRpm, FRM_UINT8 ::::0x3fb, DriveTrainData1_FA, Status_Schalter_Warmlauf_Antrieb (ST_SW_WAUP_DRV), Com_stHtgUp ::::0x3fb, DriveTrainData1_FA, Soll_Drehzahl_Leerlauf_Antrieb (TAR_RPM_IDLG_DRV), HLSDem_nSetPLo ::::0x3fb, DriveTrainData1_FA, Luftdruck_Motor_Antrieb (AIP_ENG_DRV), GlbDa_pEnv IDPUCallback: Frm_ApplCpySigChgBuffer_pfn FRAME NAME: DiaOBDMotor_FA [DIAG_OBD_ENG] (internal Gateway FA-CAN) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages messages: No messages configured messages: No messages CanDLC: 7 CanNode: CAN_B CanID: 0x397 Taskcycle: FRMSCH_EVENTTXMODE Frame time : FRMSCH_EVENTTXMODE*1 in ms Timeout: FRMSCH_EVENTTXMODE*255 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_EVENTTXMODE*1 in ms FRAME NAME: BordnetzSpannung_FA Bordnetz Spannungswert (BN_UVL) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages CanDLC: 2 CanNode: CAN_B CanID: 0x281 CanID: 0x281 Taskcycle: FRMSCH_TXMODE3 Frame time : FRMSCH_TXMODE3*1 in ms Timeout: FRMSCH_TXMODE3*1 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_TXMODE3*1 in ms Signals: ::::0x281, BordnetzSpannung_FA, Messgröße_Spannung_14V (MEAQ_U_14V), ESS_uBatt ::::0x281, BordnetzSpannung_FA, dummy (FREI), Com_DummyTx3, FRM_UINT8 FRAME NAME: StCospFuEng_FA Status Verbrauch Kraftstoff Motor (ST_COSP_FU_ENG) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages CanDLC: 8 CanNode: CAN_B CanID: 0x2c4 CanID: 0x2c4 Taskcycle: FRMSCH_TXMODE3 Frame time : FRMSCH_TXMODE3*1 in ms Timeout: FRMSCH_TXMODE3*1 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_TXMODE3*1 in ms Signals: ::::0x2c4, StCospFuEng_FA, Einspritzmenge_Kraftstoff_Motor (IJV_FU_ENG), Com_volTotFlCons ::::0x2c4, StCospFuEng_FA, Öltemperatur (OIT), SwSABMW_rDispWupRel ::::0x2c4, StCospFuEng_FA, EDA_Bereich_Soll_Position (EDA_DOM_TAR_PO), Layer_rEdaDomDesPos ::::0x2c4, StCospFuEng_FA, EDA_Soll_Position (EDA_TAR_PO), Layer_rEdaDesPos8 ::::0x2c4, StCospFuEng_FA, EDA_Ist_Position (EDA_AVL_PO), Layer_rEdaActPos ::::0x2c4, StCospFuEng_FA, EDA_Ist_Position_ID (EDA_AVL_PO_ID), Layer_stEdaActPosId ::::0x2c4, StCospFuEng_FA, ECO_Tipps_MSA (ECO_TIPS_MSA), Layer_stEcoTipMSA ::::0x2c4, StCospFuEng_FA, EDA_Soll_Position_ID (EDA_TAR_PO_ID), Layer_stEdaDesPosId ::::0x2c4, StCospFuEng_FA, dummy (FREI), Com_DummyTx3 FRAME NAME: TrqCrsh3_A Drehmoment Kurbelwelle 3 (TORQ_CRSH_3) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages CanDLC: 7 CanNode: CAN_A CanID: 0xa7 Taskcycle: FRMSCH_TXMODE1 Frame time : FRMSCH_TXMODE1*1 in ms Timeout: FRMSCH_TXMODE1*1 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_TXMODE1*1 in ms Signals: ::::0xa7, TrqCrsh3_A, Alive_Drehmoment_Kurbelwelle_3 (ALIV_TORQ_CRSH_3), Com_dTrqCrsh3CTR_A, FRM_MSGCTR ::::0xa7, TrqCrsh3_A, Ist_Drehmoment_Kurbelwelle_Fahrerwunsch_FAS (AVL_TORQ_CRSH_DVCH_DRS), SwSABMW_AvlTorqCrshDvchDrs, FRM_UINT16 ::::0xa7, TrqCrsh3_A, Anforderung_Betriebsart_Getriebestrang_FAS (RQ_OPMO_GRDT_DRS), Com_stGbxModDemFAS, FRM_UINT8 ::::0xa7, TrqCrsh3_A, Qualifier_Anforderung_Sperre_Getriebestrang (QU_RQ_ILK_GRDT), Com_stLckGbxDemQl_FX, FRM_UINT8 ::::0xa7, TrqCrsh3_A, Soll_Radmoment_Antrieb_Summe_Koordiniert (TAR_WMOM_DRV_SUM_COOTD), SwSABMW_TarWmomDrvSumCootd, FRM_UINT16 FRAME NAME: WMOM_DRV_1_A Radmoment Antrieb 1 (WMOM_DRV_1) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages CanDLC: 8 CanNode: CAN_A CanID: 0x08f Taskcycle: FRMSCH_TXMODE1 Frame time : FRMSCH_TXMODE1*1 in ms Timeout: FRMSCH_TXMODE1*1 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_TXMODE1*1 in ms Signals: ::::0x08f, WMOM_DRV_1_A, Alive_Radmoment_Antrieb_1 (ALIV_WMOM_DRV_1), Com_dWhlTrqPT1CTR_A, ::::0x08f, WMOM_DRV_1_A, Ist_Radmoment_Antriebsstrang_Summe (AVL_WMOM_PT_SUM), Com_trqWhl, ::::0x08f, WMOM_DRV_1_A, Qualifier_Ist_Radmoment_Antriebsstrang_Summe (QU_AVL_WMOM_PT_SUM) ::::0x08f, WMOM_DRV_1_A, Ist_radmoment_Antriebsstrang_Summe_Fehler_Amplitude (AVL_WMOM_PT_SUM_ERR_AMP) ::::0x08f, WMOM_DRV_1_A, Verstärkung_Antriebsstrang (REIN_PT), Com_rTrqPT, FRM_UINT16 ::::0x08f, WMOM_DRV_1_A, Qualifier_Verstärkung_Antriebsstrang (QU_REIN_PT), Com_stRTrqPTQl ::::0x08f, WMOM_DRV_1_A, CRC_Radmoment_Antrieb_1 (CRC_WMOM_DRV_1), Com_dWhlTrqPT1CHK_A, FRAME NAME: DriveTrainData1_A Daten Antriebsstrang 1 (DT_PT_1, internal Gateway FA-CAN) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages messages: No messages configured messages: No messages CanDLC: 6 CanNode: CAN_A CanID: 0x3fb Taskcycle: FRMSCH_EVENTTXMODE Frame time : FRMSCH_EVENTTXMODE*1 in ms Timeout: FRMSCH_EVENTTXMODE*255 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_EVENTTXMODE*1 in ms FRAME NAME: TrqCrsh4_A Drehmoment Kurbelwelle 4 (TORQ_CRSH_4) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages CanDLC: 8 CanNode: CAN_A CanID: 0xc2 Taskcycle: FRMSCH_EVENTTXMODE Frame time : FRMSCH_EVENTTXMODE*1 in ms Timeout: FRMSCH_EVENTTXMODE*255 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_EVENTTXMODE*1 in ms Signals: ::::0xc2, TrqCrsh4_A, Alive_Drehmoment_Kurbelwelle_4 (ALIV_TORQ_CRSH_4), Com_A_dTorqCrsh4CTR ::::0xc2, TrqCrsh4_A, CHL_Drehmoment_Kurbelwelle_4 (CHL_TORQ_CRSH_4), Com_A_ChlTorqCrsh4 ::::0xc2, TrqCrsh4_A, Ist_Drehzahl_Motor_Kurbelwelle_Low_extrapoliert (AVL_RPM_ENG_CRSH_LOW_EPL), Com_A_AvlRpmEngCrshLowEpl ::::0xc2, TrqCrsh4_A, CRC_Drehmoment_Kurbelwelle_4 (CRC_TORQ_CRSH_4), Com_A_dTorqCrsh4CHK FRAME NAME: PwrmngCtrCos_FA Powermanagement Verbrauchersteuerung (POWERMGMT_CTR_COS) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages CanDLC: 7 CanNode: CAN_B CanID: 0x3b3 Taskcycle: FRMSCH_EVENTTXMODE Frame time : FRMSCH_EVENTTXMODE*255 in ms Timeout: FRMSCH_EVENTTXMODE*0 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_EVENTTXMODE*255 in ms Signals: ::::0x3b3, PwrmngCtrCos_FA, Dummy (FREI), Com_DummyTx3 ::::0x3b3, PwrmngCtrCos_FA, Auswahl Sonderverbraucher (SLCTN_SPCOS), Layer_stSelSpCos ::::0x3b3, PwrmngCtrCos_FA, Steuerung Leistung Sonderverbraucher (CTR_PWR_SPCOS), Layer_rCtrPwrSpCosL ::::0x3b3, PwrmngCtrCos_FA, Steuerung Leistung Verbraucher (CTR_PWR_COS), Layer_stCtrPwrCos ::::0x3b3, PwrmngCtrCos_FA, Steuerung Stromzweig (CTR_CBR), Layer_stCtrCbr ::::0x3b3, PwrmngCtrCos_FA, Anforderung Standverbraucher (RQ_PCOS), Layer_stRqPCos ::::0x3b3, PwrmngCtrCos_FA, Steuerung Standverbraucher (CTR_PCOS), Layer_stCtrPCos ::::0x3b3, PwrmngCtrCos_FA, dummy (FREI), Com_DummyTx3 ::::0x3b3, PwrmngCtrCos_FA, Status_Energie_Powermanagement (ST_ENERG_PWMG), Layer_stEnrgPwrMnmt ::::0x3b3, PwrmngCtrCos_FA, dummy (FREI), Com_DummyTx3 IDPUCallback: Frm_ApplCpySigChgBuffer_pfn FRAME NAME: DiaOBDMotor_FA [DIAG_OBD_ENG] (internal Gateway FA-CAN) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages messages: No messages configured messages: No messages CanDLC: 7 CanNode: CAN_B CanID: 0x397 Taskcycle: FRMSCH_EVENTTXMODE Frame time : FRMSCH_EVENTTXMODE*1 in ms Timeout: FRMSCH_EVENTTXMODE*255 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_EVENTTXMODE*1 in ms FRAME NAME: DataBatt_FA Daten Batterie (DT_BAT) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages CanDLC: 5 CanNode: CAN_B CanID: 0x351 Taskcycle: FRMSCH_EVENTTXMODE Frame time : FRMSCH_EVENTTXMODE*255 in ms Timeout: FRMSCH_EVENTTXMODE*255 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_EVENTTXMODE*255 in ms Signals: ::::0x351, DataBatt_FA, Ist Zustand Batterie (AVL_CON_BT), Layer_stBattAct ::::0x351, DataBatt_FA, Status Ladung Batterie (ST_CHG_BT), Layer_stBattChrg ::::0x351, DataBatt_FA, Status Batterie Falsh (ST_BT_WNG), Layer_stBattWrng ::::0x351, DataBatt_FA, Status Zelldefekt (ST_CEDT), Layer_stBattSectnErr ::::0x351, DataBatt_FA, Qualitaet Zustand Batterie Kapazitaet Ist (QUAL_CON_BT_CAPE_AVL), Layer_stBattQlCapAct ::::0x351, DataBatt_FA, Qualitaet Zustand Batterie Ladezustand (QUAL_CON_BT_CHGCOND), Layer_stBattQlChrg ::::0x351, DataBatt_FA, Status Verlust Wasser (ST_LSS_WTR), Layer_stBattLosWt ::::0x351, DataBatt_FA, Status Tiefentladung (ST_EXHDCHG), Layer_stBattLowDisCh ::::0x351, DataBatt_FA, Zustand Batterie Kapazitaet Ist (CON_BT_CAPE_AVL), Layer_wBattCapAct ::::0x351, DataBatt_FA, Zustand Batterie Ladezustand (CON_BT_CHGCOND), Layer_wBattChrg ::::0x351, DataBatt_FA, Anzahl Wechsel Batterie (QUAN_ALT_BT), Layer_ctBattChng ::::0x351, DataBatt_FA, dummy (FREI), Com_DummyTx3 IDPUCallback: Frm_ApplCpySigChgBuffer_pfn FRAME NAME: FACAN_IMMO_TX Tx frames from DME for FEM, EGS and EME on FACAN CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages messages: No messages configured messages: No messages CanDLC: 8 CanNode: CAN_B CanID: 0x592 Taskcycle: FRMSCH_EVENTTXMODE Frame time : FRMSCH_EVENTTXMODE*1 in ms Timeout: FRMSCH_EVENTTXMODE*10 in ms TimeoutDFC: NULL FrameVariant: ALLMODES Scheduletime: FRMSCH_EVENTTXMODE*1 in ms IDPUCallback: MiniTp_FACAN_TxCallback FRAME NAME: ACAN_IMMO_TX Tx frames from DME for FEM, EGS and EME on ACAN CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages messages: No messages configured messages: No messages CanDLC: 8 CanNode: CAN_A CanID: 0x592 Taskcycle: FRMSCH_EVENTTXMODE Frame time : FRMSCH_EVENTTXMODE*1 in ms Timeout: FRMSCH_EVENTTXMODE*10 in ms TimeoutDFC: NULL FrameVariant: ALLMODES Scheduletime: FRMSCH_EVENTTXMODE*1 in ms IDPUCallback: MiniTp_ACAN_TxCallback FRAME NAME: DiensteID38_FA Dienste FZM (SLRDI_LCL_FZM) CanDirection: SEND DSM configuration: No DSM configuration available Bitmessages: No bit messages CanDLC: 8 CanNode: CAN_B CanID: 0x592 Taskcycle: FRMSCH_EVENTTXMODE Frame time : FRMSCH_EVENTTXMODE*50 in ms Timeout: FRMSCH_EVENTTXMODE*50 in ms TimeoutDFC: NULL FrameVariant: MODE1 Scheduletime: FRMSCH_EVENTTXMODE*50 in ms Signals: ::::0x592, DiensteID38_FA, ID2 (ID2), Com_DummyTx3 ::::0x592, DiensteID38_FA, Source of sleep readiness (FREI), Com_DummyTx3 ::::0x592, DiensteID38_FA, Sleep Ready of local bus (ST_SLRDI_LCL), Com_stSleepRdyTx ::::0x592, DiensteID38_FA, Sleep acknowledge of local bus (ST_SLP_ACK_LCL), Com_stSleepAckTx ::::0x592, DiensteID38_FA, Source of sleep readiness (FREI), Com_DummyTx3 ::::0x592, DiensteID38_FA, counter of none ready ecus (ECU_QUAN_SLRDI_NEG), Com_ctSleepNeg ::::0x592, DiensteID38_FA, first ID of not ready ECU (ECU_ID_SLRDI_NEG_0), Com_numSleepNegID0 ::::0x592, DiensteID38_FA, second ID of not ready ECU (ECU_ID_SLRDI_NEG_1), Com_numSleepNegID1 ::::0x592, DiensteID38_FA, third ID of not ready ECU (ECU_ID_SLRDI_NEG_2), Com_numSleepNegID2 ::::0x592, DiensteID38_FA, fourth ID of not ready ECU (ECU_ID_SLRDI_NEG_3), Com_numSleepNegID3